How to adjust the headlights on VAZ-2110? Adjustment of headlights VAZ-2110 own hands

To ensure the safety of managementcar headlight should be set correctly. On how to adjust the headlights on the VAZ-2110, every car owner should know. You can make the adjustment without removing the element from the machine - for this purpose there are special screws with which the beam of light is regulated in a vertical plane. In the same way, the beam is adjusted on the 2111, 2112 models. Even the more modern LADA Granta and LADA Priora models have such settings.

How to disassemble the lights

how to adjust the headlights on the vase 2110

In order to adjust the VAZ-2110 headlights with your own hands, you need to get rid of all the defects in them: repair, replace the glass, the lamp, the reflector. The order of disassembly is as follows:

  1. Disconnect the negative terminal from the battery. If the battery interferes, you can completely remove it.
  2. Remove the glass by warming it with a hair dryer. Thus, you will be able to melt the adhesive composition that is under it.
  3. Cut on the lens a small U-shaped profile.
  4. Remove the reflector made of paper. To do this, you need to unscrew the three bolts from the back.
  5. Near the hydraulic corrector there is a spring, it needs to be removed. Together with it, "rosettes" - plastic clips fixed to the reflector are dismantled.
  6. Snap the ball on the edge of the reflector.
  7. Snap the coil out of the metal to prevent the regulator from unscrewing.

If the hydraulic corrector is tightened tightly, this will cause the limiter to simply deform. In this case, a ball will exit the plastic holder, and the entire optical system will fall down.

Features of removing the block headlamp

Be sure to take into account that if you twistproofreader, you will have to replace the steel part with a rubber gasket. The problem is that the steel element of the corrector breaks down, deforms, which affects the work. This is not the best option, since it is difficult to understand when installing the rubber gasket when the headlights are in the extreme positions.adjusting the headlights of the VAZ 2110 with your own hands

In order not to lose the light, you will needre-twist the corrector. Therefore, when adjusting the VAZ-2110 headlights with your own hands, you will need to install an additional lock. Ideally suitable cotter pin. It is placed in the petals of the plastic "rose". Be sure to observe the accuracy when disassembling the block headlamp. Before first use, clean all surfaces from excess sealant. If necessary, grease the glass around the perimeter of the sealant.

Alternative tuning

Headlight adjustment for VAZ 2110

In order to adjust the headlights on the VAZ-2110, you can use an alternative method. To do this, perform the following actions:

  1. Cut the thread on the fixtures of the luminous flux regulators.
  2. Tighten the screws inside the lights and put the washers on them.
  3. Remove the plastic clips.
  4. Install the strips on which the reflectors of the far and passing beam are located.
  5. Install the washer over the bar. Still need to install the spring on it and over again the washer.
  6. The entire structure is fixed with a control nut.

Preliminary work before adjustment without disassembly

If there are no defects in the headlamp itself, you can not disassemble it, just adjust the beam of light.how to adjust the headlights of vases 2110

It is necessary to perform several preparatory actions before starting adjustment of the VAZ-2110 headlights with your own hands. The photo shows the layout of the wall. You will also need to meet the following conditions:

  1. Fully refuel the gas tank, in order to the rear of the car is lowered.
  2. Rinse all the glass on the headlights.
  3. In the trunk lay a spare, a fire extinguisher, a set of keys. In other words, everything that you usually carry with you.
  4. Check the pressure in all wheels and, if necessary, pump up.
  5. Place the vehicle on a flat surface. It is extremely important that there is an ideally flat wall or a fence next to it. The distance from it to the front of the car must be at least 8 meters.

Be sure to properly mark the vertical plane, since it depends on how accurately the light is adjusted.

Algorithm of actions for customization

Before adjusting the headlights on the VAZ-2110,you need to do all the preparatory activities. Installing the front seats of the cargo does not make sense. For more accurate adjustment (as the machine is loaded), there is a hydraulic drive. Its handle is to the left of the rudder, near the fuse block. And now about how to make the adjustment of the headlights without disassembling the elements:

  1. Install the car against the wall, the longitudinal part of it must be perpendicular to the body.
  2. Start the engine and turn on the dipped beam. It is advisable to start the engine in order not to put the battery.
  3. Turn the hydraulic control knob to the "1" position. This position corresponds to the minimum load - only the driver is in the car.
  4. Correct the direction of the light beams with the screws on the block-headlights, being guided by the scheme presented in the article.

Having reached the right direction, you can finish the job. Now, depending on the degree of congestion of the car, you just need to adjust the position of the handle of the hydraulic drive.

If you need to change the headlamp

adjusting the headlights of the vase 2110 with your own hands photo

Before adjusting the headlights on the VAZ-2110,you need to make sure of their serviceability. If the repair, which was described above, does not work, then a complete replacement of the headlamp must be made. To do this, perform the following manipulations:

  1. Disconnect from the lantern all wiring and remove the upper part of the radiator grill. To do this, it is necessary to unscrew all the bolts with a key for "10".
  2. Disconnect from turn signals of a wire and remove the hydraulic proof-reader. To do this, press the latch and turn the body of the device 90 degrees.
  3. Unscrew the fixing screws of the optical element and move the block-head back.
  4. Loosen the bolts on the upper lock and remove the "cilium".

After you unscrew the last nut, you canremove the entire lamp assembly and remove it. If it is still possible to perform repairs, do it. If not, then change the headlamp entirely. Before adjusting the headlights on VAZ-2110, be sure to repair them. So you will be able to ensure maximum reliability of optics.

Related news

How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands How to adjust the headlights on VAZ-2110 Adjustment of headlights VAZ-2110 own hands